How To Use An Adt Or Honeywell Security System With Pictures

If a motion detector is tripped, the system may not display “Ready to Arm”, but you will still be able to arm the system STAY.

Disarm: Disarms the security system, regardless of which mode the alarm is in, and clears any previous alarms or faults. The keypad beeps once. Arm Stay: Arms the security system in “stay” mode. This enables all sensors except for motion detectors. The security system beeps three times. Night Stay: Arms the security system in “night” mode. This enables all perimeter sensors, plus a few motion detectors. The motion detectors armed in night mode are set by your installer. Entry Delay: Turns the entry delay on or off. If the entry delay is off, then opening any set entry/exit door before disarming the system will immediately sound the alarm. Arm Away: Arms the security system in “away” mode. This enables all sensors, including motion detectors, doors, windows, and glass break detectors. During the exit delay, the alarm will count down the amount of time until the alarm is fully armed, and beep rapidly within the last 10 seconds. Arm Custom: Arms the security system, but allows for bypassing of up to five zones. Bypassed zones will not trigger an alarm when they are opened.

An alarm sounds immediately if a door not normally used for exit, or if any enabled sensor is tripped. If the keypad is equipped with a loud sounder, then that will be used to sound the alarm. If the keypad is not equipped, then any external sounders, along with alternating high and low-frequency continuous beeps will sound.

During the entry delay, the keypad will beep continuously until the delay ends. During the last ten seconds, the keypad will beep rapidly. If a false alarm sounds, silence the alarm by entering your security code within two minutes to avoid the monitoring center being notified. To clear the false alarm, press “Disarm” then enter your security code again.

If a motion detector is tripped, the LED will not turn green, but you will still be able to arm the system STAY.

OFF: Disarms the security system, and clears any previous alarms or faults. The keypad beeps once. AWAY: Arms the security system in “away” mode. This enables all sensors, including motion detectors, doors, windows, and glass break detectors. The security panel repeatedly beeps until the exit delay (time you have to leave the premises) ends, and beeps rapidly within the last 10 seconds. The delay resets if an exit door is opened within the last ten seconds of exit delay. STAY: Arms the security system in “stay” mode. This enables all sensors except for motion detectors. The security system beeps three times. NIGHT-STAY: Arms all perimeter sensors, plus a few motion detectors. To do so, press the stay button twice after entering your security code. The motion detectors armed in NIGHT-STAY is programmed by your security installer. INSTANT: Arms the security system in “stay” mode, but removes the entry delay. The entry delay is the grace period before the alarm sounds. The entry delay is set by the installer of the security system. The security system beeps three times. MAX: Arms the security system in “away” mode, but removes the entry delay. If the security system is not disarmed before entering the home, the alarm will sound.

During the entry delay, the keypad will beep continuously until the delay ends. During the last ten seconds, the keypad will beep rapidly. If a false alarm sounds, enter your four-digit PIN then press OFF within two minutes to avoid the monitoring center being notified. To clear the false alarm, enter your four-digit PIN again then press OFF.

Some panels do not have a built-in test mode and can only be put on test by calling the monitoring center or using their online portal.

Bypassing a zone disables it while armed. If a bypassed zone is tripped, the alarm system will simply ignore it. You have to bypass the zone every time you want to arm the security system, as bypassed zones are reset upon disarming the security system. Some systems only allow up to five zones to be bypassed.

To sound a fire alarm, press the button with a pictogram of a fire for two seconds. Alternatively, press the two buttons with arrows from the fire symbol. To sound a security alarm, press the button with a pictogram of a police shield for two seconds. Alternatively, press the two buttons with arrows from the police symbol, or press the panic button on the keychain remote. To sound a medical alarm, use a medical pendant you are wearing or press the HELP button on the medical intercom. Alternatively, press the button with a pictogram of a medical cross for two seconds, or press the two buttons with arrows from the medical button.

There will be no notification (phone call or text message) that the dispatch center has received the alarm. The police may take up to 5 minutes to arrive. Make sure that everyone knows this PIN, and make sure that it is only used in an emergency.

01 is reserved for the installer code. 02 is reserved for the master code. 03/33 is reserved for the partition code.

To add/change a user code, enter their code. The security system beeps once. To delete a user code, press # then 0. To change the permissions of that code, press # then 1 then any of the following: 0 is arm only. 1 is guest. 2 is duress code. 3 is master code. On a touchscreen panel, select the appropriate code type from the dropdown. Some panels have duress codes hardcoded into certain positions such as position 6.

When a service person does come to service your security system, check their credentials. You do not want them to break your security system even further. [3] X Trustworthy Source Federal Trade Commission Website with up-to-date information for consumers from the Federal Trade Commisson Go to source